Logo
Sitemap
Air Preparation Systems
 

Air Brake Systems >> Air Preparation Systems

Description
Dehydrator 11.3511010-01 is used in Air Brake Systems of trucks, buses, tractors and other vehicles. It is used for air drying and automatic moisture drainage.

When air pressure grows up to 1.1 MPa and then reduces to 0.8 MPa, atmospheric moisture capacity of the air, supplied into braking system, does not exceed 9095%, excluding the possibility of system failure caused by condensate freezing.

The Dehydrator makes any additional anti-freezing systems unnecessary.

Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,85 (8,5)
Drain: automatic
Dehydration efficiency, %, not less than: 75
Thread, mm: M22x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, kg: 2,55
Description
Pressure Control Valve 11.3512010 is used in Air Brake Systems of trucks, buses, wheeled tractors and other vehicles.

Provides pressure control of the air, supplied by compressor into the receivers of pneumatic system. Features a safety valve, which ensures that the resulting pressure does not exceed a specific value.

Technical specification
ON pressure, MPa (kgs/cm2), not less than: 0,65 (6,5)
OFF pressure, MPs (kgs/cm2): 0,850,02 (8,50,2)
Relief valve engagement pressure, MPa (kgs/cm2): from 0,9 to 1,05 (from 9 to 10,5)
Thread, mm: M22x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, kg: 0,865
Description
Pressure Control Valve 11.3512010-10/20 is used in Air Brake Systems of trucks, buses, trolleybuses, wheeled tractors and other commercial vehicles.

Provides pressure control of the air, supplied into vehicle's brake system.

Pressure Control Valve comes with a bracket, allowing installation of Pressure Control Valve 11.3512010-10 as a replacement for 100-3512010 and Pressure Control Valve 11.3512010-20 as a replacement for 11.3512010.

Main advantages of Pressure Control Valve 11.3512010-10/20 in comparison with Pressure Control Valve 11.3512010 are:
  • air-bleed valve

  • no compressed air leak when in compressor unload mode
Moving parts, rubber seals and springs of Pressure Control Valve 11.3512010-10/20 are unified with similar parts of Dehydrator with Pressure Regulator 14.3512010.

Technical specification
ON pressure, MPa (kgs/cm2), not less than: 0,65 (6,5)
OFF pressure, MPs (kgs/cm2), not less than: 0,85 (8,5)
Relief valve engagement pressure, MPa (kgs/cm2): from 0,95 to 1,35 (from 9,5 to 13,5)
Thread, mm: M22x1,5
Air bleed valve thread, mm: M16x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, kg: 0,67
Description
Anti Freezer 11.3515150-11 is used in Air Brake Systems of trucks, buses and wheeled tractors and other vehicles.

Used for forcing ethanol into the Air Brake System to prevent condensate freezing in the pipelines of the Brake System's devices.

Operated mechanically by pressing the pusher button.

Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,85 (8,5)
Working medium: air, ethanol
Volume of ethanol, supplied in one injection:
  • with air pressure in the inlet: 1,0 1,5

  • without air pressure in the inlet: 1,4 2,0
Thread, mm: M22x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, kg: 0,55
Description
Dehydrator with Pressure Regulator 14.3512010 is used in Air Brake Systems of trucks, buses, trolleybuses, wheeled tractors and other commercial vehicles.

It is used for dehydration, air pressure control and automatic moisture drainage.

Main advantages of Dehydrator with Pressure Regulator 14.3512010 in comparison with Dehydrator 11.3511010-01 are:
  • 20% more effective dehydrating capability for improved safety in low temperature conditions

  • No compressed air leak when in compressor unload mode (extends compressor's lifetime by reducing its operation recurrence)

  • Dehydrator's and pressure regulator's features in one device (resulting in 1.2kg reduced steel intensity)

  • Simplified wiring as a result of reduced connecting armature, piping and bracketry

  • Mounted on the same bracket as used with Dehydrator 11.3511010-01
Price 15% lower than net price of Dehydrator 11.3511010-01 and Pressure Control Valve 11.3512010

Technical specification
ON pressure, MPa (kgs/cm2), not less than: 0,65 (6,5)
OFF pressure, MPs (kgs/cm2), not less than: 0,85 (8,5)
Relief valve engagement pressure, MPa (kgs/cm2): from 0,95 to 1,35 (from 9,5 to 13,5)
Thread, mm: M22x1,5
Air bleed valve thread, mm: M16x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, kg: 0,67
Description
Dehydrator with Pressure Regulator 14.3512010-10 is used in Air Brake Systems of trucks, buses, trolleybuses, wheeled tractors and other commercial vehicles.

It is used for dehydration, air pressure control and automatic moisture drainage.

Modification 14.3512010-10 differs from 14.3512010 in longer smooth pipe, used for preventing heat transfer reduction caused by pipe dirtying.

Technical specification
ON pressure, MPa (kgs/cm2), not less than: 0,65 (6,5)
OFF pressure, MPs (kgs/cm2), not more than: 0,85 (8,5)
Relief valve engagement pressure, MPa (kgs/cm2): from 0,95 to 1,35 (from 9,5 to 13,5)
Drain: automatic
Thread, mm: M22x1,5
Air bleed valve thread, mm: M16x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, not more than, kg: 2,5
Description
Dehydrator with Pressure Regulator 14.3512010-01 is used in Air Brake Systems of trucks, buses, trolleybuses, wheeled tractors and other commercial vehicles.

It is used for dehydration, air pressure control and automatic moisture drainage.

Modification 14.3512010-01 differs from 14.3512010 in the following:
  • Has a cooler flange joint made of ribbed pipe, which improves mechanical durability and assures maintainability

  • Has a refined safety-valve duplication system

  • Changed regulation section and improved reliability of check valve in low temperature conditions

  • Improved design of bypass channel valve, providing necessary efficiency and longevity
Has a filter in the entrance lag, which ensures protection against foreign particles.

Technical specification
ON pressure, MPa (kgs/cm2), not less than: 0,65 (6,5)
OFF pressure, MPs (kgs/cm2), not more than: 0,85 (8,5)
Relief valve engagement pressure, MPa (kgs/cm2): from 1,15 to 1,4 (from 11,5 to 14,0)
Drain: automatic
Thread, mm: M22x1,5
Air bleed valve thread, mm: M16x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, not more than, kg: 2,75
Description
Dehydrator with Pressure Regulator 14.3512010-11 is used in Air Brake Systems of trucks, buses, trolleybuses, wheeled tractors and other commercial vehicles.

It is used for dehydration, air pressure control and automatic moisture drainage.

Modification 14.3512010-11 has constructional improvements similar to device 14.3512010-01 and differs in the following:
  • Air-bleed device with connecting threading M 16x1.5
More effective drying capability resulting from increased pressure (up to 1.01.07 MPa or 1010.7 kg/cm2) produced by compressor before the check valve.

Technical specification
ON pressure, MPa (kgs/cm2), not less than: 0,65 (6,5)
OFF pressure, MPs (kgs/cm2), not more than: 0,85 (8,5)
Relief valve engagement pressure, MPa (kgs/cm2): from 1,15 to 1,4 (from 11,5 to 14,0)
Drain: automatic
Thread, mm: M22x1,5
Air bleed valve thread, mm: M16x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, not more than, kg: 2,7
Description
Air Dryer 11.3536008/-10 is to be used in air brake systems of commercial vehicles for the purpose of drying and purifying the compressed air and thus preventing corrosion and condensate freezing in the circuits of the air brake system. Air Dryer improves reliability of other components of the system.

Air Dryer 11.3536008/-10 features built-in pressure regulator, safety valve, heating element, silencer, and preliminary moisture separator, designed to increase the lifespan of cartridge absorber

Technical specification
Compressor atmosphere discharge mode engagement pressure, MPa (kgs/cm2):
  • for 11.3536008: 0,81+0,02 (8,1+0,2)

  • for 11.3536008-10: 0,85+0,02 (8,5+0,2)
Compressor fill mode engagement pressure, Mpa (kgs/cm2), min: 0,7 (7,0)
Pressure, limited by safety valve, MPa (kgs/cm2): 0,95+0,21,35 (9,513,2)
Thread, mm: M22x1,5
Air bleed valve thread, mm: M16x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, not more than, kg: 4,4

Heater element specification
Rated voltage, V:
  • for 11.3536008: 12+3-1,5

  • for 11.3536008-10: 24+6-3
Nominal power consumption, W: 100 Turn-on temperature, °C: 7+2-6 Turn-off temperature, °C: 274
Description:
Replacable cartridge for Air Dryer 11.3536008/-10

Technical specification
Working pressure: 800 kPa
Maximum pressure: 1,3 MPa
Thread, mm: M39x1,5
about news products quality order feedback history fairs contacts