Logo
Sitemap
New products
 
Description:
Air Preparation Unit 11.3536006-10 is an alternative to Air Dryer ZB44 series with 4-circuit protection valve produced by KNORR-BREMSE. It consists of Air Dryer and 4-circuit Protection Valve, which are connected by steel connecting pipe. Construction advantages are decreasing of assembling costs and enlargement of lay-out variants (attitude position of the protection valve can vary by valve rotation around a 22-22 teat axle.

Technical specification:
Compressor air discharge mode engagement pressure, MPa (kgs/cm2): 0,85+0,02 (8,5+0,2)
Compressor fill mode engagement pressure, MPa (kgs/cm2), min: 0,7 (7,0)
Pressure, limited by protection valve, MPa (kgs/cm2): 0,951,35 (9,513,2)
Thread: 221,5-7, 121,5-7
Temperature range, : from minus 45 to plus 60
Dew point reserve, , min: 15
Weight, kg: 5,5

Heater Element Specification:
Rated voltage, V: 24-3
Nominal power consumption, W: 100;
ON temperature, : 7-6
OFF temperature, : 27 4
Description:
Reverse-action Hand Brake Valve is used in pneumatic braking system of trucks, buses, trolleybuses and wheel tractors. Operated mechanically by turning the handle and provides controlled compressed-air bleed from the parking brake control bus or from the reserve brake control bus.

Reverse-action Hand Brake Valve 11.3537510 gives an opportunity to realize control testing of a trucks hand brake efficiency for keeping vehicle on slope while a trailer is unbraked.

Technical specification:
Working pressure, MPa (kgs/cm2): 0,65...0,85 (6,5...8,5)
Maximum flow area equivalent to diameter of the hole, mm: 7
Thread, mm: 141,5
Connecting torque of fittings with rubber seals at thread holes, Nm: 15...25
Working temperature range, : from minus 45 to plus 60
Weight, not more than, kg: 0,73
Description:
It is used for signal transmission between clutch pedal and pneumohydraulic booster.

Technical specification:
Stroke: 42 mm
Cylinder diameter: 32
Working pressure: 1,0 MPa (10,0 kgs/cm2)
Maximum pressure: 7,0 MPa (70,0 kgs/cm2)
Description:
It is used for decrease of drivers effort, while he declutches by pedal. This device decreases drivers fatiguability and increases vehicles ergonomical characteristic by using energy of a compressed air.

Technical specification:
Working pressure, MPa (kgs/cm2): 0,65-0,85 (6,5-8,5)
Working pressure of the fluid: to 1MPa (10 kgs/cm2)
Maximum pressure: 12 MPa (120 kgs/cm2)
Conditional air flow area: more than 6mm
Force on the rod when air pressure is:
  • 0,6 MPa (6,5 kgs/cm2) - not less than 5000 N (500 kgs)
  • 0,8 MPa (8,0 kgs/cm2) - not less than 6200 N (620 kgs)
Full rod stroke, mm: 68-72
Temperature range, Ѱ: from minus 40 to plus 60
Thread: 14x1,5, 16x1,5
Weight, kg, not more than: 5,1
Description:
The Brake Valve is used in pneumatic braking system of trucks, buses, trolleybuses and wheel tractors.

It is operated mechanically by suspended pedal, ensuring that the brake chambers in each of two circuits, as well as control chambers of other pneumatic apparatus of the Brake System, are filled with compressed air following appropriate filling speed and with appropriate tracking. Fastening surface is decreased. This devise has space-saving dimensions.

If one of the Brake System's circuits is depressurized, the Brake Valve provides controllable refill of the working circuit with compressed air.

Technical specification:
Working pressure, MPa (kgs/cm2): 0,65 0,85 (6,5 8,5)
Free pusher stroke, mm: 1,9 3,0
Full opening pusher stroke, mm: 8,4 10,8
Total pusher stroke, mm: 12,5 15,7
Thread: 22X1,5
Temperature range, : from minus 45 to plus 60
Description:
Double-Main Valve 12.3562010/-10 is used in Air Brake Systems of trucks, buses, wheeled tractors, trailers and semi-trailers.

It has two inputs and one output and provides fast air bypass from the input with bigger pressure to the output.

Technical specification:
Working pressure, MPa (kgs/cm2): 0,650,80
Thread: 221,5
Temperature range, : from minus 45 to plus 60
Weight, kg: 0,42


Description:
Electrical-Pneumatic Valves 12.3745000 with 3 mm internal diameter and bayonet electro-cutoff point according to the DIN 72585-1 ensure reliable and waterproof bond. It is used in pneumatic systems of commercial vehicles and technological equipment for control stream of compressed air in pneumatic circuits. Electrical-Pneumatic Valves design allows to assemble them in blocks.

Technical specification:
Conditional pass, mm.: 1,6
Working pressure of compressed air, MPa (kgs/cm2): 0,60,8 (6,08,0)
Reaction time, s.: 0,03
Type of current: directs
Voltage, V: 24
Power consumption, W: 7
Weight, kg: 0,35
Throughput, not less than, m3/hr: 0,08


Description:
It is used for braking by standing engine while fuel feeding is turned off.

Technical specification:
Working pressure, MPa (kgs/cm2): 0,65-0,85 (6,5-8,5)
Thread: 121,5
Damer movement angle: 65
Temperature range, : from minus 45 to plus 60
Weight, kg, not more than: 5,1


Description:
It is used for smooth extinguishing of vertical drivers seat oscillation.

Technical specification:
Maximum diameter, mm: 44
Outer diameter, mm: 22
Length in compressed state, mm: 190
The force of resistance, developed in shock absorbers
during compression and impact: 4010 kgs
Rod movement speed, m/s: 0,226
Weight, kg: 0,2
about news products quality order feedback history fairs contacts